Yes, the response curve is isnt calibrated, but you can download a generic file, or you can send it somewhere to be calibrated.The build quality is good, and the frequency response was good enough in my tests with Smaart.You also dont need any title, description and ending texts in your file, so make sure they are deleted.You mentioned REW. Have you measured your room yet That will tell you what EQ can and cannot improve.
Behringer Ecm8000 Calibration File Rew Download A GenericFirst, with all due respect and aimed at the community at large, I am continually amused at so many continuously trying to reinvent the wheel regarding this process rather than simply following more standard tested configurations. Regarding eh actual equipment and configuration, one will need a CALIBRATED omni mic. The 2 cheapest (in so many ways) commonly available mics are the Behringer ECM8000 and the SuperluxDayton EMM6 - of which the Dayton exhibits much less variability - which would suggest one stick with the Dayton. The best source to obtain a reasonable cost calibrated unit is from Cross Spectrum. As far as the Behringer PS400, as has been noted, ALL that is is a phantom power unit - nothing more, as as such it is absolutely not sufficient. And yes, you can use the Behringer mixer with its multitude of addition noise inducing gain stages and EQ, where even the manufacturer brags over it ability to impart coloration similar to the 1960s British units - which while that MAY (or may not) be advantageous for someone wishing to impose special FX on vocals, it is absolutely NOT desired for a measurement mic As has been posted myriad times, the best least expensive pre-amp (and NO, this does NOT mean that this is anywhere near the best preamp for measurement purposes) if cost is the primary concern is the ART Dual USB pre amp available from BandHPhoto, normally 129, available delivered for about 69. You will also want to follow the proper calibration procedures for the setup for both frequency (done once) and also for hardware time latency (left in place) using a loopback connection that connects the output of the 2nd channel with the input of that same second channel. Behringer Ecm8000 Calibration File Rew Free To PMIf you still have questions, and I expect you will as such sites as the REW support site is helpful but rather confusing with the diagrams and reference to pre-amps as sound cards.if you need clarification feel free to PM me - and if you have either Yahoo Messenger or Skype we can quickly get you straightened out and clarify what should be a rather straightforward configuration process. Originally Posted by dragonfyr Just be sure to get the calibrated version of the for 85 from Cross Spectrum. Also, calibration down to 5 Hz is available, but you have to specifically ask for it - no extra charge. Also, you might want to read his review of the mics first - which at the moment I an having trouble locating. I might suggest contacting Cross Spectrum regarding a comparison of the Behringer versus the Dayton quality control, or lack thereof. Can I just use a non-calibrated one I cant afford 110.00 mic, only a 55 dollar one:P I am a poor university student. REW says it has a default input file for ECM8000, is it good enough. Should I just eq my room by ear My budget for this would be 100 bucks for everything. But you order the calibrated version of the mics, be they Behringer or Dayton, directly from the party who performs the calibration. And please note that in reference to your desire to EQ your room, that you CANNOT (well, more properly, MAY not) EQ non-minimum phase systems - which is precisely what most of he anomalies above 80 Hz are that result from the superposition of specular signals manifest as comb filtering. So basically, unless you identify minimum phase conditions, limit your attempts to EQ to EQing PEAKS below 80 Hz And EQ will not remediate modal nulls EQ is but one small component tool in the process of addressing modal behavior - it is not a panacea as some erroneously imagine. I am only eqing my subwoofer so there shouldnt be anything above 80 hz really. EQ can be used to reduce the level of peaks, but in most home-sized rooms the larger problem is nulls which EQ cannot improve. You mentioned REW. Have you measured your room yet That will tell you what EQ can and cannot improve.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |